General –The SaltDogg® ¾ yard spreader is a completely self-contained,
ultra-durable spreader unit designed for ice and snow control. Great for trucks with less bed room (in-bed tool boxes for example). The rugged design allows for use with salt or salt/sand mix, and is also ideal for broadcsting seed, fertilizer, game feed, etc. The complete assembly mounts easily on utility vehicles, or ¼-ton pickups, making it ideal for municipalities, shopping malls, industries, hospitals and private contractors.
MATERIAL HOPPER – Rotationally molded double-wall polymer unibody spreader with smooth angled walls to maximize material flow. Features integrated positive position mount system plus 4-piece ratchet tie-down kit. No drilling required. Molded fork slots in hopper makes for easy one man installation and removal; requires extended forks, or lift either series with 4-point tie downs.
AUGER – Screw-type auger system travels the length of the hopper floor, providing maximum material flow at a continuous rate. An independent spinner/auger controller allows for both independent spinner speed and an infinitely adjustable ratio between spinner and auger.
MATERIAL FLOW/OUTPUT – Salt, 2.2 cu. ft. / minute; Salt-Sand, 1.3 cu. ft. / minute. Spread width is variable from 5 to 38 feet.
SPINNER CHUTE ASSEMBLY – An 11.5" polymer disc with four fins is connected to a 3/4" diameter shaft. The spreading material is guided from the stainless steel trough to the spinner plate through an enclosed heavy-duty poly chute and spinner assembly with an external deflector. The extra-wide adjustable deflector protects the rear and under carriage of the vehicle, and allows for complete directional spread control and full or compact spread. Total spread path ranges from 5' to 38'. A convenient spring-latch locking mechanism allows the spinner assembly to be easily removed for cleaning/storage.
ELECTRIC MOTORS – Two ultra-quiet 12-volt DC direct-drive motors power the auger and spinner, and are encased in a heavy-duty poly housing along with the independently powered vibrator. The wiring harness is constructed of 10-gauge automotive wire with non-combustible sheathing (-50° to -105° C). An in-cab console features independent controls for the auger, spinner and vibrator.
STANDARD EQUIPMENT – 1/4" black powder coated steel top screen. Heavy-duty poly-vinyl tarp with reinforced corners and tie-down kit. Heavy-duty 12 VDC vibrator, rated at 210 foot pounds for maximum performance. Spreader hold-down kit.
SHPE0750: Overall Length, 53"; Width, 48"; Capacity Struck, 0.6 cu. yd.; Capacity Rounded, 0.75 cu. yd.; Recommended use, Utility Vehicles or ¼-Ton pickups.

IDEAL FOR MEDIUM AND HEAVY DUTY COMMERCIAL APPLICATIONS.
General –The 1-1/2 yard 1500 SHPE series electric polymer Salt Dogg spreaders are completely self-contained, ultra-durable spreader units designed for ice and snow control. The rugged design allows for use with salt or salt/sand mix. The complete assembly mounts easily on pickup, dump and platform trucks, making it ideal for municipalities, shopping malls, industries, hospitals and private contractors.
MATERIAL HOPPER – Rotationally molded double-wall polymer unibody spreader with smooth angled walls to maximize material flow. Features integrated positive position mount system plus 4-piece ratchet tie-down kit. No drilling required. Molded fork slots in hopper makes for easy one man installation and removal; requires extended forks, or lift either series with 4-point tie downs.
AUGER – Screw-type auger system travels the length of the hopper floor, providing maximum material flow at a continuous rate. An independent spinner/auger controller allows for both independent spinner speed and an infinitely adjustable ratio between spinner and auger.
MATERIAL FLOW/OUTPUT – Salt, 2.2 cu. ft. / minute; Salt-Sand, 1.3 cu. ft. / minute. Spread width is variable from 5 to 38 feet.
SPINNER CHUTE ASSEMBLY – An 11.5" polymer disc with four fins is connected to a 3/4" diameter shaft. The spreading material is guided from the stainless steel trough to the spinner plate through an enclosed heavy-duty poly chute and spinner assembly with an external deflector. The extra-wide adjustable deflector protects the rear and under carriage of the vehicle, and allows for complete directional spread control and full or compact spread. Total spread path ranges from 5' to 38'. A convenient spring-latch locking mechanism allows the spinner assembly to be easily removed for cleaning/storage.
ELECTRIC MOTORS – Two ultra-quiet 12-volt DC direct-drive motors power the auger and spinner, and are encased in a heavy-duty poly housing along with the independently powered vibrator. The wiring harness is constructed of 10-gauge automotive wire with non-combustible sheathing (-50° to -105° C). An in-cab console features independent controls for the auger, spinner and vibrator.
STANDARD EQUIPMENT – 1/4" black powder coated steel top screen. Heavy-duty poly-vinyl tarp with reinforced corners and tie-down kit. Heavy-duty 12 VDC vibrator, rated at 210 foot pounds for maximum performance. Spreader hold-down kit.
SHPE1500 & SHPE1500X: Overall Length, 92" (requires 77" minimum bed length. Fits all 8' beds and most standard 6' beds); Capacity Struck, 1.45 cu. yd.; Width, 50.5"; Height, 37.5"; Recommended use, 3/4 or 1-Ton trucks.

______________________________________________

SHPE2000

1.3 – 2.3 Yard – All hopper spreaders are completely self-contained, ultra-durable spreader units designed for ice and snow control. The rugged design allows for use with salt, sand and other materials. The complete assembly mounts easily on pickup, dump and platform trucks making it ideal for municipalities, shopping malls, industries, hospitals and private contractors.
STAINLESS STEEL MATERIAL HOPPER – Feature high-quality grade 304 stainless steel components, including: Hopper, Hopper Supports, Hopper Floor, Gussets, Spinner Chute Assembly, Deflectors and Engine Hood. Electrically welded ends and sides sloped at 45º are constructed with channel formed top edges. Vertical supports add extra strength to the unit. The single lift point on the cross support beam is located at the unit ’s center of gravity to allow for easy loading and unloading.
CONVEYOR – The conveyor is made of 12"wide all-steel pintle chain with 3/16"x 3/4"cross bars. Chain strength is 11,000 lbs.per strand;22,000 lbs. total weight. The drive sprockets are 6-tooth cast iron, on a 1-1/8" diameter shaft. The conveyor chain has an adjustment range of 3-1/2". The drive shaft has heavy-duty, sealed, self-aligning ball bearings with grease fittings. The idler drum has heavy-duty 1" diameter ball bearings.
CONVEYOR GEAR CASE – Gear is constructed of aluminum bronze, worm gear is hardened steel and ground. Housing is made of durable cast iron. Gear ratio is 20:1 with 1" input shaft and 1-1/8"output shaft on tapered roller bearings.
FEEDGATE – Lever operated with a friction lock for accurate adjustment.
SPINNER CHUTE ASSEMBLY – Feature high-quality grade 304 stainless steel Spinner Chute Assembly, Deflectors and Engine Hood. A polymer disc with four fins is connected to a 3/4"diameter shaft secured on two pillow block bearings. The spreading material is guided from the conveyor to the spinner plate through an enclosed chute with internal and external deflectors. Adjustable deflectors allow for complete directional spread control and full or compact spread. Total spread radius ranges from 2' to 25'. The extra wide rear deflector protects the rear and under carriage of the vehicle.
ENGINE – Heavy-duty 10.5 horsepower industrial/commercial Briggs & Stratton gasoline engine. Engine comes equipped with alternator and 12 volt electric starter with in-cab start/stop and electric throttle control (standard). Entire engine is completely protected by the convenient hinged hood.
ELECTRIC THROTTLE CONTROL – Throttle control unit allows for full-range of throttle settings,including idle and full choke,via the in-cab hopper control box. Use of electric throttle control eliminates cable freezing, binding and breaking.
CLUTCH – 12 volt DC electric clutch has a three-position in-cab switch, for greater control and material economy. Also allows for low speed operation and spot spreading.

72" Spreaders – Body Side Length, 6'; Overall Length, 89"; Capacity Struck, 1.3 cu.yd.; Capacity Rounded, 1.6 cu.yd.; Width, 47"; Height, 32 –1/2"; Recommended Use, 3/4 or 1-Ton Trucks.

96" Spreaders – Body Side Length, 8'; Overall Length, 113"; Capacity Struck, 1.8 cu.yd.; Capacity Rounded, 2.1 cu.yd.; Width, 47"; Height, 32 –1/2"; Recommended Use, 3/4 or 1-Ton Trucks.

120" Spreaders – Body Side Length, 10'; Overall Length, 137"; Capacity Struck, 2.3 cu.yd.; Capacity Rounded, 2.7 cu.yd.; Width, 47"; Height, 32–1/2"; Recommended Use, Heavy-duty flatbed or long dump Trucks.

General – All hopper spreaders are completely self-contained, ultra-durable spreader
units designed for ice and snow control. The rugged design allows for use with salt, sand and other materials. The complete assembly mounts easily on pickup, dump and platform trucks making it ideal for municipalities, shopping malls, industries, hospitals and private contractors.
POLYMER MATERIAL HOPPER – Rotationally molded double-wall polymer unibody spreader with smooth angled walls to maximize material flow. Features integrated positive position mount system plus 4-piece ratchet tie-down kit. No drilling required.
CONVEYOR – The conveyor is made of 12" wide all-steel pintle chain with 3/16"x 3/4"cross bars. Chain strength is 11,000 lbs.per strand;22,000 lbs. total weight. The drive sprockets are 6-tooth cast iron, on a 1-1/8" diameter shaft. The conveyor chain has an adjustment range of 3-1/2". The drive shaft has heavy-duty, sealed, self-aligning ball bearings with grease fittings. The idler drum has heavy-duty 1" diameter ball bearings.
CONVEYOR GEAR CASE – Gear is constructed of aluminum bronze, worm gear is hardened steel and ground. Housing is made of durable cast iron. Gear ratio is 20:1 with 1" input shaft and 1-1/8"output shaft on tapered roller bearings.
FEEDGATE – Lever operated with a friction lock for accurate adjustment.
SPINNER CHUTE ASSEMBLY –Feature high-quality grade 304 stainless steel Spinner Chute Assembly, Deflectors and Engine Hood. A polymer disc with four fins is connected to a 3/4"diameter shaft secured on two pillow block bearings. The spreading material is guided from the conveyor to the spinner plate through an enclosed chute with internal and external deflectors. Adjustable deflectors allow for complete directional spread control and full or compact spread. Total spread radius ranges from 2' to 25'. The extra wide rear deflector protects the rear and under carriage of the vehicle.
ENGINE – Heavy-duty 10.5 horsepower industrial/commercial Briggs & Stratton gasoline engine. Engine comes equipped with alternator and 12 volt electric starter with in-cab start/stop and electric throttle control (standard). Entire engine is completely protected by the convenient hinged hood.
ELECTRIC THROTTLE CONTROL – Throttle control unit allows for full-range of throttle settings,including idle and full choke,via the in-cab hopper control box. Use of electric throttle control eliminates cable freezing, binding and breaking.
CLUTCH – 12 volt DC electric clutch has a three-position in-cab switch, for greater control and material economy. Also allows for low speed operation and spot spreading.

96" Spreaders – Body Side Length, 8'; Overall Length, 113"; Capacity Struck, 1.8 cu.yd.; Capacity Rounded, 2.1 cu.yd.; Width, 47"; Height, 32 –1/2"; Recommended Use, 3/4 or 1-Ton Trucks.

General – The 4-yard, SHPE series SaltDogg spreaders are completely self-contained, ultra–durable spreader units designed for ice and snow control. The rugged design allows for use with salt or salt/sand mix. The complete assembly mounts easily on dump, platform and utility trucks, making it ideal for municipalities, shopping malls, industries, hospitals and private contractors.
Material hopper – Rotationally molded polymer hopper with smooth angled walls to maximize material flow.
Auger – 5.5" Dia. screw-type auger system travels the length of the hopper floor, providing maximum material flow at a continuous rate. An independent spinner/auger controller allows for both independent spinner speed and an infinitely adjustable ratio between spinner and auger.
Material flow/output – Salt, 3.2 cu. ft./minute; Salt/Sand, 2.3 cu. ft./minute. Spread width is variable from 5 to 38 feet.
Spinner chute assembly – A 16" polymer disc with six fins is connected to a 3/4" diameter shaft. The spreading material is guided from the stainless steel trough to the spinner plate through an enclosed heavy-duty polymer chute and spinner assembly with an external deflector. The extra-wide adjustable deflector protects the vehicle and allows for complete directional spread control and full or compact spread. Total spread path ranges from 5' to 38'. A convenient spring-latch locking mechanism allows the spinner assembly to be removed for cleaning/storage.
Electric Gear motors – Two 12-volt DC direct-drive motors power the auger and spinner, and are encased in a heavy-duty poly housing along with the independently powered vibrator. The wiring harness is constructed of 10-gauge automotive wire with non-combustible sheathing (-50°C to -105°C). An in-cab console features independent controls for the auger, spinner and vibrator.
Standard equipment – 1/4" black powder coated steel top screen. Heavy-duty poly-vinyl tarp with reinforced corners. Heavy-duty 12 VDC vibrator, rated at 400 foot pounds for maximum performance. Spreader hold-down kit.
SHPE4000 – Overall Length, 100" (Hopper 90"); Width, 74"; Height, 43"; Weight, 878 lbs.; Capacity Struck, 4.0 cu. yd.; Recommended Use, 1-Ton Dump Bodies.